Just back from Create Make Learn 2015

documentation

Just back from visiting our most excellent faculty member, Lucie deLaBruere’s Create, Make, Learn week long workshop. She had 30+ K12 teachers, 19 of which are getting Marlboro optional credit, studying all day, all week, up a Champlain College and The Generator. Champlain College folks were doing Creating with Chrome when I was there. Here’s some photos of what was going on at the two strands at The Generator.

Teaching Kids to Fly Micro Quadracopters, (and Perhaps a Life Lesson) at the Champlain Mini Maker Faire in Vermont on Lake Champlain.

documentation, General, How-Tos, Make & Fablab, Product Reviews, Video

As an experiment I gave micro quadcopter flight lessons to kids this weekend at the Champlain Mini Maker Faire. I learned a lot. My back is sore from picking up crashed drones ever 10 seconds for two days because it was a very popular booth! The lesson I learned (perhaps a life lesson) was, “When in trouble, turn off the motor; and fall gently to the grass, then get back up and try again.” In other words, resilience, persistence, and the practiced discipline to avoid uncontrolled crashes that prevent trying again, in favor of controlled crashes your craft can survive unscathed. 

screen-shot-2017-03-03-at-4-49-58-pm

Photo Slideshow
Link to Slideshow

On breaks, I managed to get some video to test the craft’s camera. With a lot of crashes, I ended up with shots of a rocket launch, lake views, inside flights, and in-tent flights of the Northern New England Drone User Group next to my table.  

The micro quad I used for this test is about the size of my hand. It’s safe since its blades spin in place if they hit skin, leaving only a sting. And it had prop guards and I stood right next to the kids with my hand near the throttle. They cost about $70 (including an HD camera now, which amazes me). Here’s a great unboxing and review of the model I usedUnboxing the Hubsan X4 H107C v2 HD. Considering it’s cost and size, and that is it designed for mostly indoor use, I think the video is remarkable. But the site is remarkable too!

The experiment worked. Kids lined up both days. It was very exhausting, since I was the only one manning the table both days (note to self). I’m still sore from running around finding the crashed copters in the grass every few minutes. It took me a day and half to realize the kids loved finding the crashed copters…duh…

The kernel I found to the teaching was helping these young new pilots turn off the motors and have a controlled crash before they had an uncontrolled crash. Controlled crashes are when you stop all the motors and the craft tumbles out of the air. This little copter doesn’t usually get hurt if it lands from any height on grass. It’s spars have break away parts that clip back together and it’s very light. It does get hurt in high speed crashes with the motors grinding the props into the ground. 

It takes a lot of practice to fight the human instinct to power up when the craft starts to get in trouble. I saw almost 100% of kids and adults power up whenever the craft got out of control or near obstacles! And everyone, even ace pilots, get in trouble. Human nature though is to save the craft and keep it flying. But, powering up almost always leads to higher speed crashes, often with the motor on causing the props to try to spin the grass, on fingers, rocks, dirt, etc. Even worse, after a crash, our instinct is to rush over to the downed craft. Rushing over to a downed craft often makes one’s hand slip on the controller causing the motors keep on struggling. This then was our challenge, to practice fighting on initial instincts. 

We only broke one craft in two days of flying, and that was because it hit a metal bar on the tent roof at just the wrong angle at full speed and I wasn’t quick enough to stop the power that one time.

Most people quickly break small RC copters and miss out on the joy of flying. I hope now there are a few more folks you there who can control their crashes, try again, and slowly near to fly in interesting places and ever higher.

Makerspace Expo Room at Dynamic Landscapes 2014 Conference in Burlington Vermont.

documentation, General, Projects

I co-coordinated, with Donna Sullivan-MacDonald of the Vermont Library Association, a Makerspace Expo Room at this years Dynamic Landscapes conference in Burlington, VT at Champlain College’s Fireside lounge.

The open format with hands-on activities, student projects and local Maker-folk turned out to be a great success! Here’s some media.

Screen Shot 2014-05-19 at 4.47.04 PM

Screen Shot 2014-05-19 at 4.47.54 PM

Keynote speaker Gary Stager recording video of an excellent student maker project.

Keynote speaker Gary Stager recording video of an excellent student maker project.

IMG_3569 IMG_3570 IMG_3571 IMG_3572 IMG_3573 IMG_3575 IMG_3595 IMG_3597 IMG_3598 IMG_3599
IMG_3601 IMG_3602 IMG_3603 IMG_3604 IMG_3605 IMG_3606

Custom 3D printer swag. Dynamic Landscapes 2014 ring

Custom 3D printer swag. Dynamic Landscapes 2014 ring. Customized from thingiverse object: http://www.thingiverse.com/thing:314813